The insulation material in a cable is used to isolate the conductor from one another and from ground, as well as provide the necessary mechanical strength. The fundamental requirement of the insulation in an el

Test Samples are required to condition at regulated temperature and humidity conditions before the actual test. The conditioning helps reduce the variation in results due to external environmental conditions. &

Laboratory Hot Set Test Apparatus is designed to determine the elongation & permanent set of insulation of armored and unarmored single, twin, three , four and multi-core cross linked Polyethylene (XLPE) in

The procedure of test for cracking due to environmental stresses on electric polyethylene insulation or sheath of cables Water Bath : Double Walled water bath : 15 x 15 x 18 (LBH in Inches) Temperature Con

Smoke Density Apparatus is used for measuring & observing the relative amount (Density) of smoke produced by the burning (combustion) or decomposition of Plastic, Cables etc. under controlled conditions. 

The test is intended to verify the effectiveness of the separator between the non tinned conductor and insulation.   Salient Features  Sold Bath Size : 4 x 4 x 4 (LBH in inches)

Thermoplastic and Poly vinyl Chloride substances when exposed to heat undergo many types of physical and chemical changes. The extent and type of change that takes place depends upon the severity of exposure of

The Instruments is used for heat Ageing test under oxygen air pressure for insulation & sheath of electric cables. This apparatus is also used for estimating the relative resistance of vulcanized rubber to

For certain locations it may be important to use a cable which retards flame in case of fire and is self – extinguishing when the source of fire is removed. This test is carried out on finished cables to veri

Two Roll Mill is used for mixing two or more compounds in a homogeneous mixture. This Mixture is then molded into samples for further testing. Salient Features       Model : SSI 511 TRPF

Critical limiting Oxygen Index apparatus is used for determining the minimum percentage of Oxygen required to just support flaming combustion of a material at room temperature in FTA mode or at Higher Temperat

Compounds based on halogenated polymers and compounds containing halogenated additives emits harmful Halogen Acid Gas while burning. These gases are corrosive and can prove harmful to property and humans in cas

For certain locations it may be important to use a cable which retards flame in case of fire and is self – extinguishing when the source of fire is removed. This test is carried out on finished cables to veri

Thermoplastics and PVC  (Plasticized Polyvinyl Chloride) materials when exposed to continuous heat, degenerates and emit harmful acidic gases. The instrument is manufactured for testing PVC materials against t

This Test instrument is designed to covers a laboratory Procedure for testing of bunch cables mounted vertically to determine their relative ability to resist flame prorogation. The objective of the fire test i

When the Cables / Electrical Equipments are subjected top extreme cold for a considerable duration of time, they may become hardened and stiff. Such hardness and stiffness cause cracking of the insulation or sh

When the Cables / Electrical Equipment are subjected top extreme cold for a considerable duration of time, they may become hardened and stiff. Such hardness and stiffness cause cracking of the insulation or she

For certain locations it may be important to use a cable which retards flame in case of fire and is self – extinguishing when the source of fire is removed. This test is carried out on finished cables to veri

Cracks and deformation occur when the material is bend or wound under cold conditions. The apparatus is deigned to wound the cable samples on standardized mandrels under cold conditions.   Salient Featu

Most materials when exposed to extreme cold over a period of time become hard and brittle. This test is designed to study the effect of cold temperatures on material under mechanical shock. Salient Feature Â

Thermoplastics and PVC materials when exposed to continuous heat tend to soften. In this condition when they are subjected to mechanical pressure, they have a tendency to deform at the location of pressure resu

Various standards for test of Plastics, Wires & Cables, and Polymer Compounds require test samples of specific shape and size for conducting test on different materials. Hydraulic Hot press is a basic appar

The insulation material in a cable is used to isolate the conductor from one another and from ground, as well as provide the necessary mechanical strength. The fundamental requirement of the insulation in an el

Thermoplastics and PVC materials when exposed to continuous heat, degenerates and emit harmful acidic gases. The instrument is manufactured for testing PVC materials against their thermal stability at higher te

The UL test serves as a preliminary indication for Plastics components acceptability for use as part of a device or appliance with respect to its flammability. The instrument is designed for both Vertical an

Thermoplastic and Poly vinyl Chloride substances when exposed to heat undergo many types of physical and chemical changes. The extent and type of change that takes place depends upon the severity of exposure of

Double walled Borosilicate Glass Chimney provides the ideal test environment for testing Limiting Oxygen Index for at both ambient as well as elevated temperature. Salient Features       G

Smoke Density Apparatus is used for measuring & observing the relative amount (Density) of smoke produced by the burning (combustion) or decomposition of Plastic, Cables etc. under controlled conditions.

When the Cables / Electrical Equipments are subjected top extreme cold for a considerable duration of time, they may become hardened and stiff. Such hardness and stiffness cause cracking of the insulation or sh

Copper Purity Apparatus is designed to determine the purity of copper by electrolysis method. The sample containing copper is dissolve in sulfuric -& nitric acid mixture and a regulated current is passed

SSI Hot Water Bath are designed to maintain uniform Temperature across the complete chamber and provide controlled enviroment for Heating, Curing, or testing various properties under elevated temperature of wat

This instrument is designed to testing cables required to maintain circuit integrity when subject to fire alone where the test conditions is based upon a flame with a controlled heat output corresponding to a t

The Press is deigned to accept various types of Dumb Bell and Sample Dies for cutting the sample. Salient Features       Model : SSI 510 DPLT (Dumb Bell cutting press with lever type handle) Force A

Correct and accurate sample is necessary for result accuracy and repeatability. The Sample Die is designed to produce equal sized samples for testing Limiting oxygen Index Test Apparatus.   Salie

Compounds based on halogenated polymers and compounds containing halogenated additives emits harmful Halogen Acid Gas while burning. These gases are corrosive and can prove harmful to property and humans in cas

Thermal Ageing Test Instrument helps in study of Ageing Process on various material. Thermoplastic and Poly Vinyl Chloride substances when exposed to heat undergo many types of physical and chemical changes. Th

Most materials when exposed to extreme cold over a period of time become hard and brittle. Cold Impact test is designed to study the effect of cold temperatures on material under mechanical shock.    

Dumb Bell is the most widely used shape for testing various samples for their physical and other properties.     Salient Features       Die Material :  Die Steel Overall Length :  75 mm,

The Test is designde to test the evpouration or fading of color when exposed to direct sunlight.   Salient Features Constrution :  Aluminum / Mild Steel Body with wooden / aycralic battens Top

SSI Ovens are designed to maintain uniform Temperature across the complete chamber and provide controlled enviroment for Heating, Curing, Drying or testing various properties under elevated temperature.  

This instrument is designed to testing cables required to maintain circuit integrity when subject to fire alone where the test conditions is based upon a flame with a controlled heat output corresponding to a t

Thermoplastic and Electrometric substances when exposed to heat undergo many types of physical and chemical changes. The extent and type of change that takes place depends upon the severity of exposure of the s

Limiting Oxygen Index / Critical Limiting Oxygen Index apparatus is used for determining the minimum percentage of Oxygen required to just support flaming combustion of a material at room temperature in FTA mod

Smoke Density Apparatus is used for measuring & observing the relative amount (Density) of smoke produced by the burning (combustion) or decomposition of Plastic, Cables etc. under controlled conditions. 

Cracks and deformation occur when the material is bend or wound under cold conditions. The apparatus is deigned to wound the cable samples on standardized mandrels under cold conditions.     Salien

During the armoring process and subsequently during laying of the cable, the armor wires are subjected to torsion stress.  The test is conducted to evaluate the torsion resistance of the wire. Salient Featu

Critical limiting Oxygen Index apparatus is used for determining the minimum percentage of Oxygen required to just support flaming combustion of a material at room temperature in FTA mode or at Higher Temperatu

SSIPL vacuum ovens are required in almost every institution for drying, moisture removal by heating in vacuumed environment. Salient Features       Model : SSI 558 VOC (Vacuum Oven Cylindrical Model

Correct and accurate sample is necessary for result accuracy and repeatability. The Sample Die is designed to produce equal sized samples for testing Smoke Density for any sample. Salient Feature  

Thermoplastic and electrometric substances when exposed to heat undergo many types of physical and chemical changes. The extent and type of change that takes place depends upon the severity of exposure of the s

Any compound when burned emits a cocktail of gases, which are harmful to humans. The significant of these gases is increased if the area under fire is compact and can have serious effects on humans and other ma

Laboratory Hot Set Test Apparatus is designed to determine the elongation & permanent set of insulation of armoured and unarmoured single, twin, three , four and multi-core cross linked Polyethylene (XLPE)

Lab Two Roll Mill is designed to mix / knead rubber based material where in heat is emitted on kneading. The rollers are cooled by circulating water inside the roller cavity for rapid and uniform cooling.

Thermoplastic and Poly vinyl Chloride substances when exposed to heat undergo many types of physical and chemical changes. The extent and type of change that takes place depends upon the severity of exposure of

This method covers a laboratory Procedure for testing of bunch cables mounted vertically to determine their relative ability to resist flame prorogation. The test is conducted in open air environment only.  &n

Compounds based on halogenated polymers and compounds containing halogenated additives emits harmful Halogen Acid Gas while burning. These gases are corrosive and can prove harmful to property and humans in cas

The UL test serves as a preliminary indication of a plastics material acceptability for use as part of a device or appliance with respect to its flammability. The instrument is designed for both Vertical and H

The Press is deigned to accept various types of Dumb Bell and Sample Dies for cutting the sample.     Salient Features       Model : SSI 510 DPFW (Dumb Bell cutting press with Fly Wheel) F

Smoke Density Apparatus is used for measuring & observing the relative amount (Density) of smoke produced by the burning (combustion) or decomposition of Plastic, Cables etc. under controlled conditions.

Laboratory Hot Set Test Apparatus is designed to determine the elongation & permanent set of insulation of armored and unarmored single, twin, three , four and multi-core cross linked Polyethylene (XLPE) in

Smoke Density Apparatus is used for measuring & observing the relative amount (Density) of smoke produced by the burning (combustion) or decomposition of Plastic, Cables etc. under controlled conditions.

The UL test serves as a preliminary indication of a plastics material acceptability for use as part of a device or appliance with respect to its flammability. The instrument is designed for both Vertical and H

The Instruments is used for heat Ageing test under oxygen air pressure for insulation & sheath of electric cables. This apparatus is also used for estimating the relative resistance of vulcanized rubber to

The machine is used to reduce the thickness of XLPe sheet to prepare final sample sheet of upto 0.8 mm thickness for testing.   Salient Feature       Working Principle : Two Rollers pushes the sa

Thermoplastics and PVC  (Plasticized Polyvinyl Chloride) materials when exposed to continuous heat, degenerates and emit harmful acidic gases. The instrument is manufactured for testing PVC materials against t